»Vault Agent Windows Service
Vault Agent can be run as a Windows service. In order to do this, you need to register Vault Agent with the Windows Service Control Manager. After Vault Agent is registered, it can be started like any other Windows service.
Note: These commands should be run in a PowerShell session with Administrator capabilities.
There are multiple ways to register Vault Agent as a Windows service. One way is to use
best if the path to your Vault binary and its associated agent config file do not contain spaces.
sc.exe can be
pretty tricky to get working correctly if your path contains spaces, as paths containing spaces must be quoted,
and escaping quotes correctly in a way that makes
sc.exe happy is non-trivial. If your path contains spaces, or you prefer not to use
alternative is to use the
New-Service is less picky about the method used to escape quotes, and can sometimes be easier. Examples of
both will be shown below.
Important Note: Ensure the executable path of the service is quoted, especially when it contains spaces, to avoid potential privilege escalation risks.
If you use
sc.exe, make sure you specify
sc.exe explicitly, and not just
sc. The command below shows the creation
of Vault Agent as a service, using "Vault Agent" as the display name, and starting automatically when Windows starts.
binPath argument should include the fully qualified path to the Vault executable, as well as any arguments required.
PS C:\Windows\system32> sc.exe create VaultAgent binPath= "C:\vault\vault.exe agent -config=C:\vault\agent-config.hcl" displayName= "Vault Agent" start= auto [SC] CreateService SUCCESS
Note that the spacing after the
= in all of the arguments is intentional and required.
If you receive a success message, your service is registered with the service manager.
If you get an error, please verify the path to the binary and check the arguments, by running the contents of
binPath= directly in a PowerShell session and observing the results.
The syntax is slightly different for
New-Service, but the gist is the same. The invocation below is equivalent to the
sc.exe one above.
PS C:\Windows\system32> New-Service -Name "VaultAgent" -BinaryPathName "C:\vault\vault.exe agent -config=C:\vault\agent-config.hcl" -DisplayName "Vault Agent" -StartupType "Automatic" Status Name DisplayName ------ ---- ----------- Stopped VaultAgent Vault Agent
As mentioned previously,
New-Service is easier to use if the path to your Vault executable and/or agent config contains spaces.
Below is an example of how to configure Vault Agent as a service using a path with spaces.
PS C:\Windows\system32> New-Service -Name "VaultAgent" -BinaryPathName '"C:\my dir\vault.exe" agent -config="C:\my dir\agent-config.hcl"' -DisplayName "Vault Agent" -StartupType "Automatic" Status Name DisplayName ------ ---- ----------- Stopped VaultAgent Vault Agent
Note that only the paths themselves are double quoted, and the entire
BinaryPathName is wrapped in single quotes, in order
to escape the double quotes used for the paths.
If anything goes wrong during this process, and you need to manually edit the path later, use the Registry Editor to find
the following key:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\VaultAgent. You can edit the
at that key to the correct path.
There are multiple ways to start the service.
- Using the
- Using the
- Go to the Windows Service Manager, and look for VaultAgent in the service name column. Click the
Startbutton to start the service.
PS C:\Windows\system32> sc.exe start VaultAgent SERVICE_NAME: VaultAgent TYPE : 10 WIN32_OWN_PROCESS STATE : 4 RUNNING (STOPPABLE, NOT_PAUSABLE, ACCEPTS_SHUTDOWN) WIN32_EXIT_CODE : 0 (0x0) SERVICE_EXIT_CODE : 0 (0x0) CHECKPOINT : 0x0 WAIT_HINT : 0x0 PID : 6548 FLAGS :
PS C:\Windows\system32> Start-Service -Name "VaultAgent"
Note that in the case where the service was started successfully,
New-Service does not return any output.